View PW-82520R3-530L_6661232.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? data device corporation 105 wilbur place bohemia, new york 11716 631-567-5600 fax: 631-567-7358 www.ddc-web.com for more information contact: technical support: 1-800-ddc-5757 ext. 7771 features ? self-contained 3-phase motor controller operates as current or voltage controller 1, 3 and 10 amp output current radiation tolerant total dose: 100 krads seu: > 100 mev/mg/cm 2 1.5% linearity 3% current regulating accuracy user-programmable compensation 10 khz - 100 khz pwm frequency complementary four-quadrant operation holding torque through zero current cycle-by-cycle current limit non-radiation tolerant versions of this product are also available (see pw-82520/21n data sheet) description the pw-82520r (100vdc) is a high performance, radiation tolerant, current regulating torque loop controller designed to accurately regu- late the current in the motor windings of 3-phase brushless dc and brush dc motors. the pw-82520r is a completely self-contained motor controller that converts an analog input command signal into motor current and uses the signals from hall-effect sensors in the motor to commutate the current in the motor windings. the motor current is internally sensed and processed into an analog signal. the current signal is summed together with the command signal to produce an error sig- nal that controls the pulse width modulation (pwm) duty cycle of the output, thus controlling the motor current. the pw-82520r perform- ance can be tuned by utilizing the internal error amplifier and the external proportional/integral (pi) regulator network components to match motor characteristics. applications the pw-82520r is ideal for space and radiation tolerant applications requiring current regulation and/or holding torque at zero input com- mand. system applications that can use the pw-82520r are: pumps, actuators, antenna position, environmental control and reaction/momentum wheel systems using brushless and brush motors. available in a 1 and 3 amp small dip-style and a 10 amp flat- pack hybrid package, the pw-82520r is suitable for applications with limited printed circuit board area. ? 2001 data device corporation make sure the next card you purchase has... pw-82520r radiation tolerant 3-phase dc motor torque controller
2 data device corporation www.ddc-web.com pw-82520r f-03/06-0 figure 1. pw-82520r block diagram drive a drive b drive current c phase a phase a phase b phase b phase c phase c vbus+ a pwm logic circuitry commutation logic ha hb hc 5.0v 10k 10k 10k vbus? rsense pwm in + + 10.0k 5.0v error amplifier 100 - - + - + + amp command buffer 100 50k 50k 50k 50k hall a command out command in - command in + enable v dd supply gnd v ee pwm out command gnd v cc +5v error amp out error amp in current monitor out r s + hall b hall c case gnd +15v sync in v dr tach out case tach circuit vbus+ c vbus+ b v cc rtn +5v rtn dir out 470pf
3 data device corporation www.ddc-web.com pw-82520r f-03/06-0 i oc i op i cl i offset r on r c v f a a a ma ? ? ? ? v a a a ma ? ? ? ? v 10 20 14 +100 0.055 0.075 0.06 0.08 .6 3 8 4.75 +20 0.18 0.27 0.06 0.08 .85 11 -100 3.25 -20 pulse width 50sec figure 7, v cmd = 0v +25c +85c +25c +85c i d = 10a i oc i op i cl i offset r on r c v f pulse width 50sec figure 7, v cmd = 0v +25c +85c +25c +85c i d = 3a i oc i op i cl i offset r on r c v f output (pw-82520r0) output current continuous output current pulsed current limit current offset output on-resistance output conductor resistance diode forward voltage drop output (pw-82520r3) output current continuous output current pulsed current limit current offset output on-resistance output conductor resistance diode forward voltage drop table 1. pw-82520r absolute maximum ratings (tc = +25c unless otherwise specified) parameter symbol value units command input + continuous output current pw-82520r1 pw-82520r3 pw-82520r0 -5v to -15v +5v supply +5v to +15v +15v supply bus voltage i oc v ee v cc v dd v dr 15.0 1 3 10 -17.5 +5.5 +17.5 +17.5 100.0 vdc a a a vdc vdc vdc vdc table 2. pw-82520r specifications (unless otherwise specified, vbus=28vdc, v dr =+15v, v cc = +5v, v dd =+5v, v ee =-5v, tc = 25c, ll = 500 h, 100krad, pwm in = pwm out at ? free running frequency) parameter output (pw-82520r1) output current continuous output current pulsed current limit current offset output on-resistance output conductor resistance diode forward voltage drop pulse width 50sec figure 7, v cmd = 0v +25c +85c +25c +85c i d = 1a symbol test conditions 1.3 -20 min typ max units 1 3 2.25 +20 0.60 0.90 0.06 0.08 .65 a a a ma ? ? ? ? v peak output current (pulsed, t = 50 s) pw-82520r1 pw-82520r3 pw-82520r0 i peak 3.0 8.0 20.0 a a a command input - v cmd - 15.0 vdc logic inputs enable , sync in, ha, hb, hc, error amp in, pwm in v ih 7.0 vdc vbus+ a,b,c vdc vbus- to gnd voltage differential v gnddif 0v to v dd +1.0 vdc v cmd + tach out / dir out v oh 40 vdc tach out / dir out i ol 10 ma
4 data device corporation www.ddc-web.com pw-82520r f-03/06-0 table 2. pw-82520r specifications (continued) (unless otherwise specified, vbus=28vdc, v dr =+15v, v cc = +5v, v dd =+5v, v ee =-5v, tc = 25c, ll = 500 h, 100krad, pwm in = pwm out at ? free running frequency) parameter symbol test conditions min typ max units switching characteristics (pw-82520r1) upper drive turn-on rise time turn-off fall time lower drive turn-on rise time turn-off fall time t r t f t r t f rise time = 90% to 10% of vbus fall time = 10% to 90% of vbus i o = 1a 75 30 50 60 ns ns ns ns switching characteristics (pw-82520r3) upper drive turn-on rise time turn-off fall time lower drive turn-on rise time turn-off fall time t r t f t r t f rise time = 90% to 10% of vbus fall time = 10% to 90% of vbus i o = 3a 150 150 160 130 ns ns ns ns switching characteristics (pw-82520r0) upper drive turn-on rise time turn-off fall time lower drive turn-on rise time turn-off fall time t r t f t r t f rise time = 90% to 10% of vbus fall time = 10% to 90% of vbus i o = 10a 200 200 200 200 ns ns ns ns current monitor amp (pw-82520r1/r3/r0) current monitor offset output current output resistance rout ioc = 0a -10 -10 +10 +10 1 mvdc ma ? current monitor amp (pw-82520r3) current monitor gain 1.33 v/a current monitor amp (pw-82520r0) current monitor gain 0.40 v/a current monitor amp (pw-82520r1) current monitor gain 4 v/a current command transconductance ratio pw-82520r1 pw-82520r3 pw-82520r0 non-linearity temperature coefficient of g g tested using circuit shown in figure 7 io = 1a io = 3a io = 10a 0.24 0.73 2.40 -1.5 0.25 0.75 2.50 0.038 0.26 0.77 2.60 +1.5 a/v a/v a/v % fsr % fsr/c vbus+ supply nominal operating voltage vnom 18 28 70 vdc +15v supply voltage current disabled ( pw-82520r1/r3/r0) enabled pw-82520r1 pw-82520r3 pw-82520r0 enable = high enable = low enable = low enable = low v dr i dr i dr i dr i dr +13.5 +15.0 8 18 40 +16.5 100 15 25 60 vdc a ma ma ma +5v supply voltage current v cc i cc +4.5 +5.0 40 +5.5 60 vdc ma +5v to +15v supply voltage current v dd i dd +4.5 35 +16.5 50 vdc ma -5v to -15v supply voltage current v ee i ee -16.5 40 -4.5 50 vdc ma propagation delay td (on) td (off) from 0.8v on enable to 90% of vbus from 2.4v on enable to 10% of vbus 40 20 s s
5 data device corporation www.ddc-web.com pw-82520r f-03/06-0 pwm in + peak voltage - peak voltage frequency pw-82520r1/r3 pw-82520r0 linearity error duty cycle v p + v p - f pwm f pwm lin d.c. vcc = 4.5 - 5.5v 2.3 -2.8 10 10 -2 49 2.5 -2.5 50 2.8 -2.3 110 55 +2 51 v v khz khz % % pwm out free run frequency pw-82520r1/r3 pw-82520r0 stability, temperature f pwm f pwm full temp range 95 47.5 100 50 0.5 105 52.5 2.0 khz khz % hall signals ( ha, hb, hc) logic 0 logic 1 v il v ih 1.4 0.8 vdc vdc table 2. pw-82520r specifications (continued) (unless otherwise specified, vbus=28vdc, v dr =+15v, v cc = +5v, v dd =+5v, v ee =-5v, tc = 25c, ll = 500 h, 100krad, pwm in = pwm out at ? free running frequency) parameter symbol test conditions min typ max units sync in low high duty cycle sync range as % of free-run frequency input impedance v il v ih d.c. r in 2.4 49 100 50 10 0.8 51 120 vdc vdc % % k ? isolation case to ground 500 vdc hipot 10 m ? tach out/ dir out output voltage iomax v ol i o @ 1 ma 0.4 10 vdc ma vdc v v/c +4 800 2 -4 v cmd command in+/- differential input input offset input offset drift vdc v/s s to 0.1% +5.8 3 1.4 -5.8 v o = 0.2 - 4.5v v clamp command out internal voltage clamp slew rate settling time v il v ih enable enabled disabled 2.0 0.8 vdc vdc thermal (pw-82520r1/r3/r0) junction temperature case operating temperature case storage temperature tj t c t cs -55 -65 +150 +125 +150 c c c thermal (pw-82520r3) thermal resistance junction-case case-air j-c c-a 9 10 c/w c/w thermal (pw-82520r0) thermal resistance junction-case case-air j-c c-a 4 5.5 c/w c/w thermal (pw-82520r1) thermal resistance junction-case case-air j-c c-a 25 10 c/w c/w weight pw-82520r1/r3 pw-82520r0 1.7 (48) 2.9 (82) oz (g) oz (g) radiation total dose dose rate seu at let ( linear energy transfer ) level latch-up immune 100 0.5 100 100 krad rad/sec mev/mg/cm 2 mev/mg/cm 2 lead solder 10sec @300c
6 data device corporation www.ddc-web.com pw-82520r f-03/06-0 introduction the pw-82520r is a radiation hardened, 3-phase high perform- ance current control (torque loop) motor controller hybrid, which provides true four-quadrant control through zero current (refer to figure 1. pw-82520r block diagram). its high pulse width modulation (pwm) switching frequency makes it suitable for operation with low inductance motors. the pw-82520r hybrids can accept either single-ended or differential mode command signals. the current gain can be easily programmed to match the end user system requirements. the addition of an externally wired compensation network provides the user with optimum control of a wide range of loads. the pw-82520r uses single point current sense technology with an internal non-inductive hybrid sense resistor (r sense ), which yields a highly linear current output over the full -55c to +125c military temperature range. the output current non-linearity is less than 1.5% and the total error due to all the factors such as offset, initial component accuracy, etc., is maintained well below 3% of the full scale rated output current. the hall sensor interface for current commutation has built-in decoder logic that ignores illegal codes and ensures that there is no cross conduction. the hall sensor inputs are internally pulled up to +5v and can be driven from open-collector outputs. the pwm frequency can be programmed externally by adding a capacitor from pwm out to pwm gnd. multiple pw-82520r's can be synchronized in two ways: 1) by using one device as a master and connecting its pwm out pin to the pwm in of all the other slave devices, or 2) by applying a master sync pulse from an external source to the pwm in pins on all devices to be synchronized. the enable input signal provides quick start and shutdown of the internal pwm. in addition, built-in under voltage fault protec- tion turns off the output in case of improper power supply volt- ages. the hybrid features dual current limiting functions. the input command amplifier output is limited to 5v, limiting the motor current under normal operation. in addition, there is a cycle-by-cycle current limit, which kicks in to protect the hybrid as well as the load (see table 2 for i cl limits). basic operation and advantages the pw-82520r utilizes a complementary four-quadrant drive technique to control current in the load. the complementary drive has the following advantages over standard drives: 1. holding torque in the motor at zero commanded current 2. linear current control through zero 3. no deadband at zero the complementary drive design produces a 50% pwm duty cycle in response to a zero current command. during a zero cur- rent command the benefit of a complementary 4 quadrant drive over a standard 4 quadrant is as follows: complementary (figures 2, 3a) complementary drives produce a bi-directional holding torque by driving a balanced bi-polar current into the motor that has an average value of zero. during the first quarter of the pwm cycle (starting at time zero on figure 3a) the mosfet's, phase a upper (ua) and phase b lower (lb) (figure 2), are turned on. this allows current flow from phase a to phase b to increase to +imax. during the second quarter of the pwm cycle, the first pair of tran- sistors, ua and lb are turned off and a second pair phase a lower (la) & phase b upper (ub) (figure 2) are turned on. this allows the current in phase a & b from the previous quarter cycle to decrease from imax to zero. the average current during the first two-quarter cycles is positive. during the third quarter of the pwm cycle, the second pair of switches ub & la remain on allowing current to flow, in the neg- ative direction, from phase b to phase a and increase to ?imax as shown in figure 3a. during the fourth quarter of the pwm cycle, the first pair of switches ua & lb are turned on while the second pair of switch- es ub & la are turned off, to allow the current in the inductor to decrease to zero. the average current in the phases for the third and fourth quarter cycles is negative. the positive current (phase a to b) in the first two-quarter cycles produces a torque in one direction and the negative current (phase b to a) in the third and fourth quarter cycles produces a torque in the opposite direction. the average of the two oppos- ing torques results in a net zero or holding torque. non-complementary (figures 2, 3b) non-complementary drives produce a unidirectional torque by applying a unipolar current into the motor that has an average positive value as shown in figure 3b. v bus phase a upper phase a lower phase b upper phase b lower rsense phase a phase b phase c - + off off on on figure 2. complementary 4-quadrant drive first half of pwm cycle
7 data device corporation www.ddc-web.com pw-82520r f-03/06-0 during the first half of the pwm cycle the mosfet's, phase a upper and phase b lower, are turned on to provide current into the phases. during the second half of the pwm cycle the drive is in dead time, all transistors are turned off, the motor current continues to flow in the same direction through the device diodes, until it decays to zero. current flowing in to and out of the phases produces a net torque in one direction. major advantages the advantage of a complementary 4-quadrant drive over a standard 4-quadrant drive is that it provides holding torque dur- ing a zero current command. the motor current at 50% duty cycle is simply the magnetizing current of the motor winding. using the complementary 4-quadrant technique allows the motor direction to be defined by the duty cycle. relative to a given switch pair, i.e. phase a upper and phase b lower, a duty cycle greater than 50% will result in a clockwise rotation whereas a duty cycle less than 50% will result in a count- er clockwise rotation. therefore, with the use of average current mode control, direction can be controlled without the use of a direction bit and the current can be controlled through zero in a very precise and linear fashion. the pw-82520r contains all the circuitry required to close an average current mode control loop around a complementary 4- quadrant drive. the pw-82520r use of average current mode control simplifies the control loop by eliminating the need for slope compensation and by eliminating the pole created by the motor inductance. slope compensation and the pole created by the motor inductance are two limitations normally associated with implementing standard 4 quadrant current mode controls. figure 3b. standard 4 quadrant drive pwm cycle functional pin descriptions vbus+a, vbus+b, vbus+c the vbus+ supply is the power source for the motor phases. the normal operating voltage is 28vdc and may vary from +18 to +70vdc with respect to vbus-. the power stage mosfets in the hybrid have an absolute maximum vbus+ supply voltage rating of 100v. the user must supply sufficient external capaci- tance or circuitry to prevent the bus supply from exceeding the maximum recommended voltages at the hybrid power terminals under any condition. power-on sequence ( important! ) the vbus+ should be applied at least 50ms after v dd and v ee to allow the internal analog circuitry to stabilize. if this is not pos- sible, the hybrid must be powered up in the "disabled" mode. vbus- this is the high current ground return for vbus+. this point must be closely connected to supply gnd for proper operation of the current loop. v cc (+5v supply) and v cc rtn these inputs are used to power the digital circuitry of the hybrid. v dr (+15v supply) this input is used to power the gate driver circuitry for the output mosfets. there is no power consumption from v dr when the hybrid is disabled. v dd (+5v to +15v supply), and v ee (-5v to -15v supply) these inputs can vary from 5v to 15v as long as they are symmetrical. v dd and v ee are used to power the small signal analog circuitry of the hybrid. please note that using 5v supply will reduce the quiescent power consumption by approximately 60% when compared to 15v operation. ua la ub lb 0 drive switches and phase current vs. time on off on off on off on off phase current switches time (quarter phase) 12 3 4 1 2 3 4 ua la ub lb 0 drive switches and phase current vs. time on off on off on off on off switches phase current time (half phase) 1 2 3 4 figure 3a. complementary 4-quadrant drive pwm cycle
8 data device corporation www.ddc-web.com pw-82520r f-03/06-0 supply gnd supply gnd is the return for the v dr ,v ee , v dd supplies. the phase current sensing technique of the pw-82520r requires that vbus- and supply gnd (see figures 6 and 7) be con- nected together externally (see vbus- supply). case gnd this pin is internally connected to the hybrid case. in some appli- cations the user may want to tie this to ground for emi consid- erations. hall a, b, c signals these are logic signals from the motor hall-effect sensors. they use a phasing convention referred to as 120 degree spacing; that is, the output of ha is in phase with motor back emf voltage vab, hb is in phase with vbc, and hc is in phase with vca. logic ?1? (or high ) is defined by an input greater than 2.4vdc or an open circuit to the controller; logic ?0?(or low) is defined as any hall voltage input less than 0.8vdc. internal to the pw- 82520r are 10k pull-up resistors tied to +5vdc on each hall input. the pw-82520r will alternately operate with hall phasing of 60 electrical spacing. if 60 commutation is used, then the output of hc must be inverted as shown in figures 4 and 5. figure 4 illustrates the hall sensor outputs along with the cor- responding back emf voltage they are in phase with. hall input signal conditioning when the motor is located more than two feet away from the pw- 82520r controller or is in a noisy electrical environment the hall inputs require filtering from noise. it is recommended to use a 100 ? resistor in series with the hall signal and a 2000 pf capac- itor from the hall input pin to the hall supply ground pin as shown in figures 6 and 7. phase a, b, c these are the power drive outputs to the motor and switch between vbus+ input and vbus- input or become high imped- ance (see table 3). enable the enable input is an active low (l) logic signal that enables or disables the internal pwm. in the disable mode (h), the pwm is shut down and the outputs, phase a, phase b and phase c, are in an "off" state and no voltage is applied to the motor. tach out the tach out provides a tachometer signal that is a square wave with a frequency relative to motor speed and is derived from the three hall inputs ha, hb, hc. the tachometer circuitry combines these three signals into a single pulse train as a 50%- duty-cycle pulse. there are three pulses that occur every 360 electrical degree. the number of pulses per motor revolution is formulated below: dir out the dir out indicates the direction the motor is rotating, clock- wise (cw) for a lo, or counterclockwise (ccw), indicated as a logic hi. current monitor out this is a bipolar analog output voltage representative of motor current. the current monitor out will have the same scal- ing ( 4v for full scale current) as the command in inputs. sync in this input, as shown in figure 9, is used to synchronize the pwm switching frequency with an external clocking device. the pwm switching frequency can be pulled to up-to 20% faster than its free running frequency. pwm in the pwm comparator inputs are used to control the pwm pulse width. pwm out or an external triangular waveform is connect- ed to this pin. tf x 60 pr pr = x 3 (e.g., 6 pulses/revolution for a 4 pole motor) p 2 rpm = p = number of motor poles pr = number of pulses per revolution tf = tach output frequency cycles/second the motor rpm is: where: hall-effect sensor phasing vs. motor back emf for cw rotation (120 commutations) 300 0 60 120 180 240 300 360 /0 60 v ab v bc v ca back emf of motor rotating cw cw ha hb hc hc in phase with v ab in phase with v bc in phase with v ca in phase with v ac (60?) figure 4. hall phasing s hc ha 120 n hb 120 n hc 120 remote position sensor (hall) spacing for 120 degree commutation 60 60 remote position sensor (hall) spacing for 60 degree commutation s ha hb hc figure 5. hall sensor spacing warning: never apply power to the hybrid without connect- ing either pwm out or an external triangular waveform to pwm in! failure to do so may result in one or more outputs latching on.
9 data device corporation www.ddc-web.com pw-82520r f-03/06-0 phase a phase a phase b phase c vbus- phase b vbus+ c phase c hall c hall b hall a r4 r3 r2 100 100 100 c3 2000pf c4 2000pf c5 2000pf ha hb hc case gnd pwm in pwm out +5v to +15v supply gnd -5v to -15v command gnd command in - command in + error amp out command out error amp input current monitor out enable c6 c7 10k 10k r1 r5 + + + gnd +28v motor bldc pw-82520r v dd gnd v ee command signal enable - - - optional current monitor out cext + + v dr v cc +5v supply +15v supply +15v vbus+ b vbus+ a sync in sync in { c1 { { { { { { figure 6. voltage control hook-up phase a vbus- phase b vbus+ b phase c hall c hall b hall a case gnd pwm in pwm out +5v supply supply gnd +15v supply command gnd command in - command in + error amp out command out error amp input current monitor out enable c6 c7 10k, 0.5% 10k r2a 10k, 0.5% r2b 1meg r7 c1 4700pf r1 + + + pw-82520r v dd gnd v ee command signal enable - - - optional cext + + v dr v cc +5v to +15v -5v to -15v vbus+ c vbus+ a phase a phase b phase c r4 r3 r2 100 100 100 c3 2000pf c4 2000pf c5 2000pf ha hb hc gnd +28v motor bldc +15v tach dir 10k 10k tach out dir out { { { { { { { c1 sync in sync in figure 7. torque (current) control hook-up
10 data device corporation www.ddc-web.com pw-82520r f-03/06-0 pwm frequency the pwm frequency from the pw-82520r1/r3 (pw-82520r0) pwm out pin will free-run at a frequency of 100khz 5khz (50khz 2.5khz). the pwm frequency is user adjustable from 100khz (50khz) down to 10khz through the addition of an external capacitor. the pwm triangular waveform generated internally is brought out to the pwm out pin. this output, or an external triangular waveform generated by the user, may be connected to pwm in on the hybrid. pwm out this is the output of the internally generated pwm triangular waveform. it is normally connected to pwm in. the frequency of this output may be lowered by connecting an npo capacitor (cext) between pwm out and command gnd. the pwm fre- quency is determined by the following formulas: error amp in, error amp out these are the input and output pins for the error amplifier and are used for compensation. compensation the pi regulator in the pw-82520r can be tuned to a specific load for optimum performance. figure 8 shows the standard current loop configuration and tuning components. by adjusting r1, r2 and c1, the amplifier can be tuned. the value of r1, c1 will vary, depending on the loop bandwidth requirement. command in+, command in- , command ground, command out these are the connection pins for the command amplifier. the command amplifier has a differential input that operates from a 4vdc full-scale analog current command. the command ampli- fier output signal is internally limited to approximately 5vdc to prevent the amplifier from saturating. the input impedance of the command amplifier is 50k ? . pw-82520r1, r3: pw-82520r0: 33.0e-6 16.5e-6 330pf + c ext pf 330pf + c ext pf the pw-82520r can be used either as a current or voltage mode controller. when used as a torque controller (current mode), the input command signal is processed through the com- mand buffer, which is internally limited to 5vdc. the output of the buffer (command out) is summed with the current monitor output into the error amplifier. external compensation is used on the error amplifier, so the response time can be adjusted to meet the application. when used in the voltage mode, the voltage command signal is applied to the command amplifier to control the voltage applied to the motor. the command amplifier output is coupled into the error amplifier. the error amplifier directly varies the pwm duty cycle to control the voltage applied to the motor phase. the nominal pwm frequency in the voltage mode is 50% with zero volts applied to the command input. the pwm duty cycle is var- ied by the voltage applied to the command input according to the transfer function, 12% per volt applied to the command input. the duty cycle range of the output voltage is limited to approximate- ly 5-95% in both current and voltage modes. command gnd command gnd is used when the command buffer is used sin- gle-ended and the command in- or command in+ is tied to command gnd. transconductance ratio and offset when the pw-82520r is used in the current mode, the com- mand inputs (command in+ and command in-) are designed such that 4vdc on either input, with the other input connected to ground will result in full-scale current (continuous output current: (ioc) - refer to table 2) flow into the load. the dc cur- rent transfer ratio accuracy is 5% of the rated current including offset and initial component accuracy. the initial output dc cur- rent offset with both command in+ and command in- tied to the ground will be as shown in table 2 (ioffset) when measured using a load of 0.5mh and 1.0w at ambient room temperature with standard current loop compensation (see figure 8). the winding phase current error shall be within the cumulative limits of the transconductance ratio error and the offset error. sync period 0v 5v 50% duty cycle figure 9. sync input signal external pi regulator 10.0 k r1 4700 pf c1 1 meg error amp input command out current monitor out r2a 10.0 k r2b 10.0 k - + o error amp out 470 pf r7 100 figure 8. standard pi current loop
11 data device corporation www.ddc-web.com pw-82520r f-03/06-0 single event upset the hybrid shall be single event upset (seu) immune and still meet the requirements of table 2 for a linear energy transfer (let) level > 100 mev/mg/cm 2 . latch-up the hybrid is latch-up immune and meets the requirement of table 2 for a let (linear energy threshold) level > 100 mev/mg/cm 2 . note: 100krad (si) total dose of radiation is usually two to three times the operational level of commercial and military satel- lites. this is a large cost saving for the end users since lot acceptance tests (lat) are usually not required. brush motor operation the pw-82520r can also be used as a brush motor controller for current or voltage control in an h-bridge configuration. the pw-82520r would be connected as shown in figure 10. all other connections are as shown in either figures 6 or 7 depending on voltage or current mode operation. the hall inputs are wired per table 4. a positive input command will result in positive current to the motor out of phase a. optional features external sensing resistor an external sense resistor can be connected to replace the inter- nal resistor if this option is required. please contact factory for this option. rs + rs + is the high side of the sense resistor used for non-scaled test purposes only. accuracy is not a guaranteed parameter. output current output current derating as a function of the hybrid case temper- ature is provided in figures 11 and 12. the hybrid contains internal pulse by pulse current limit circuitry to limit the output current during fault conditions. (see table 2) current limit accuracy is +10/-15%. thermal operation it is necessary that the bottom surface (heat sink surface - fig- ures 13 and 14) of the pw-82520r be mounted to a heat sink. this heat sink shall have the capacity to dissipate heat generat- ed by the hybrid at all levels of current output, up to the peak limit, while maintaining the case temperature limit as per fig- ure 11. radiation total dose the hybrid shall operate, as specified in table 2, when subject- ed to a total dose radiation environment of 100krad (si) at a dose rate of 0.5 rad/sec. warning! the pw-82520r does not have short circuit pro- tection. the pw-82520r must see a minimum of 100h inductive load phase-to-phase or enough phase-to-phase line-to-line resistance to limit the continuous output current to less than i oc at all times. operation into a short or a condition that requires excessive output current will damage the hybrid. table 3. commutation truth table inputs outputs enable command in hall b c a l pos 1 0 1 l h z l pos 1 0 0 l z h l pos 1 1 0 z l h l pos 0 1 0 h l z l pos 0 1 1 h z l l pos 0 0 1 z h l l neg 0 0 1 z l h l neg 0 1 1 l z h l neg 0 1 0 l h z l neg 1 1 0 z h l l neg 1 0 0 h z l l neg 1 0 1 h l z h - - - - z z z 1=logic voltage >2.4vdc, 0=logic voltage < 0.8vdc * direction is based on the convention shown in figure 4. actual motor set up might be different. table 4. hall inputs for h-bridge controller inputs outputs enable command in ha hb hc ph b ph c ph a l positive 1 1 0 z l h l negative 1 1 0 z h l h - 1 1 0 z z z figure 10. brush motor hook-up phase a phase a phase c vbus- phase b vbus+ b phase c hall c hall b hall a c1 gnd +28v + +5v +5v vbus+ c vbus+ a { { { { { { { a b c phase dir cw cw cw cw cw cw ccw ccw ccw ccw ccw ccw - polarity dir out l l l l l l h h h h h h x
12 data device corporation www.ddc-web.com pw-82520r f-03/06-0 -50 -25 0 25 50 75 100 125 0 0.2 0.4 0.6 0.8 1.0 1.2 pw-82520r1 amps case temperature (?c) -50 -25 0 25 50 75 100 125 0.5 1.0 1.5 2.0 2.5 3.0 pw-82520r3 amps case temperature (?c) 3.5 -50 -25 0 25 50 75 100 125 0 2 4 6 8 10 12 pw-82520r0 amps case temperature (?c) figure 11. output current for continuous commutation (electrical > 600rpm, vbus+ = 28v, pwm = 50khz) pw-82520r0 power dissipation there are two major contributors to power dissipation in the motor driv- er: conduction losses, and switching losses. an example calculation is shown below: vbus = +28 v (bus voltage) i oa = 3 a, i ob = 7 a (see figure 12) f pwm = 25 khz (switching frequency) ton = 36 s, t = 40 s (90% duty cycle) (see figure 12) ron = 0.055 ? (on-resistance, see table 2) rc = 0.080 ? (conductor resistance, see table 2) ts1 = tf = 200 ns, ts2 = 2tr = 400 ns (see table 2, figure 12) i motor rms = 4.87 amps 1. transistor conduction losses (p t ) p t = (imotor rms) 2 x (ron) p t = (4.87) 2 x (0.055) p t = 1.30 watts ( 7 * 3 + (7 - 3) 2 )( 36 ) 3 i motor rms = 40 ( i ob i oa + (i ob - i oa ) 2 )( ton t ) 3 i motor rms = 2. switching losses (p s ) ps = [ vbus ( i oa (ts1) + i ob (ts2) ) fo] / 2 ps = [ 28 ( 3 (200 x10 -9 ) + 7 (400 x10 -9 ) ) 25x10 3 ] / 2 ps = 1.19 watts transistor power dissipation ( p q ) pq = p t + p s pq = 1.30 + 1.19 = 2.49 watts output conductor dissipation p c = (imotor rms) 2 x (rc) p c = (4.87) 2 x (0.080) p c = 1.90 watts 3. transistor power dissipation for continuous commutation (electrical > 600rpm) pqc = pq (0.33) pqc = (2.49) x (0.33) pqc = 0.82 watts 4. total hybrid power dissipation p total = (pq + pc) x 2 p total = (2.49 + 1.90) x 2 p total = 8.78 watts t i ob t on i oa vbus i o t s2 t s1 figure 12. output characteristics
13 data device corporation www.ddc-web.com pw-82520r f-03/06-0 phase b function pin function 1 vbus+ a 41 tach out 2 vbus+ a 40 dir out 3 phase a 39 hall b 4 phase a 38 hall a 5 vbus+ b 37 hall c 6 vbus+ b 36 enable 7 phase b 35 v cc 8 34 v cc rtn 9 vbus- 33 v dr 10 vbus- 32 sync in 11 r s + 31 v dd 12 r s + 30 supply gnd 13 vbus+ c 29 v ee 14 vbus+ c 28 n/c 15 phase c 27 n/c 16 phase c 26 current moni- tor out 25 error amp in 24 error amp out 23 command out 22 command in - 21 command in + 20 command gnd 19 pwm out 18 pwm in 17 case gnd table 5a. pin functions pw-82520 r1 and r3 pin 1.400 0.005 (35.58 0.127) 1.150 0.005 (29.21 0.127) pin no.1 contrasting color bead 0.100 0.005 typ (2.54 0.127) 24 eq. sp. @ 0.100 = 2.400 0.010 (@ 2.54 = 60.96 0.254) 2.600 0.005 (66.04 0.127) 0.150 0.005 typ (3.81 0.127) 15 eq. sp. @ 0.150 = 2.250 0.010 (@ 3.81 = 57.15 0.254) 0.250 max (6.35) 0.250 0.010 (6.35 0.254) 0.030 0.002 dia typ (0.762 0.051) 0.018 0.002 dia typ (0.457 0.051) bottom view side view notes: 1. dimensions in inches (mm). 2. lead identification numbers are for reference only. 41 1 17 16 heat sink surface figure 13. mechanical outline (r1 & r3)
14 data device corporation www.ddc-web.com pw-82520r f-03/06-0 3.110 (78.994) (max) 25 eq. sp. @ 0.100 = 2.500 (2.540 = 63.500) (tol. noncum) 0.300 (7.620) 26 0.25 (6.35) 1.60 (40.64) 27 0.150 (3.810) (typ) 43 1 16 eq. sp.@ 0.150 = 2.400 (3.810 = 60.960) (tol. noncum) pin numbers for reference only 1.860 (47.244) 2.110 (53.594) (max) 0.05 (1.27) x 45? chamfer (denotes pin 1) 0.12 (3.05) 0.040 0.002 dia (1.016 0.051) (17 plcs) 0.050 (1.270) 0.500 (12.70) (min) (typ) 0.020, 0.002 dia (0.508, .051) (26 plcs) 0.140 (3.556) 0.255 (6.477) (max) 0.100 (2.54) (typ) 0.25 (6.35) (typ) 0.147, +0.002, -0.005 dia (3.734, +0.051, -0.127) (4 holes) 2.850 (72.390) 0.125 0.010 (3.175 0.254) 0.350 (8.890) top view side view notes: 1. dimensions in inches (mm). tol = 0.005 (0.127) 2. lead identification numbers are for reference only. heat sink surface figure 14. mechanical outline (r0) command out function pin function 1 case gnd 43 n/c 2 n/c 42 phase c 3 pwm in 41 phase c 4 pwm out 40 vbus+ c 5 command gnd 39 vbus+ c 6 command in+ 38 7 command in- 37 rs+ 8 36 vbus- 9 error amp out 35 vbus- 10 error amp in 34 phase b 11 current moni- tor out 33 phase b 12 n/c 32 vbus+ b 13 n/c 31 vbus+ b 14 v ee 30 phase a 15 supply gnd 29 phase a 16 v dd 28 vbus+ a 17 sync in 27 vbus+ a 18 v dr 19 vcc rtn 20 vcc 21 enable 22 hall c 23 hall a 24 hall b 25 dir out table 5b. pin functions pw-82520 r0 pin 26 tach out rs+
15 data device corporation www.ddc-web.com pw-82520r f-03/06-0 ordering information pw-82520rx- x x x x supplemental process requirements (mandatory selection of l, q, y, z for process requirements of mil-prf-38534 selections): l = 100% pull test q = 100% pull test and pre-cap source inspection y = one lot date code and 100% pull test z = one lot date code, pre-cap source inspection and 100% pull test blank = none of the above (only applies to process requirement options 0 or 9) other criteria: 0 = no x-ray 1 = x-ray process requirements: 0 = standard ddc processing, no burn-in 1 = mil-prf-38534 compliant (note 1) 3 = mil-prf-38534 compliant with pind testing (note 1) 4 = mil-prf-38534 compliant with solder dip (note 1) 5 = mil-prf-38534 compliant with pind testing and solder dip (note 1) 9 = standard ddc processing with solder dip, no burn-in temperature range: 1 = -55c to +125c 2 = -40c to +85c 3 = 0c to +70c 4 = -55c to +125c with variables test data 5 = -40c to +85c with variables test data 8 = 0c to +70c with variables test data rating/package: 1 = 1a/dual in-line 3 = 3a/dual in-line 0 = 10a/flat package notes: 1. mil-prf-38534 compliant products include 320 hours of burn-in and 100% non-destruct pull test. ?supplemental process requirements? must be an l, q, y, z, for mil-prf-38534 compliant parts. 2. devices are not compliant with the rha requirements stipulated in mil-prf-38534, appendix g. parameters specified are derived from initial qualification testing and component (asic) manufacturers published data. 3. these products contain tin-lead solder finish as applicable to solder dip requirements. table 1 1015 (note 1) , 1030 (note 2) burn-in notes: 1. for process requirement "b*" (refer to ordering information), devices may be non-compliant with mil- std-883, test method 1015, paragraph 3.2. contact factory for details. 2. when applicable. 3000g 2001 constant acceleration c 1010 temperature cycle a and c 1014 seal 2009, 2010, 2017, and 2032 inspection condition(s) method(s) mil-std-883 test standard ddc processing for hybrid and monolithic hermetic products
data device corporation registered to iso 9001:2000 file no. a5976 r e g i s t e r e d f i r m ? u 16 f-03/06-0 printed in the u.s.a. 105 wilbur place, bohemia, new york, u.s.a. 11716-2482 for technical support - 1-800-ddc-5757 ext. 7771 headquarters, n.y., u.s.a. - tel: (631) 567-5600, fax: (631) 567-7358 southeast, u.s.a. - tel: (703) 450-7900, fax: (703) 450-6610 west coast, u.s.a. - tel: (714) 895-9777, fax: (714) 895-4988 united kingdom - tel: +44-(0)1635-811140, fax: +44-(0)1635-32264 ireland - tel: +353-21-341065, fax: +353-21-341568 france - tel: +33-(0)1-41-16-3424, fax: +33-(0)1-41-16-3425 germany - tel: +49-(0)89-150012-11, fax: +49-(0)89-150012-22 japan - tel: +81-(0)3-3814-7688, fax: +81-(0)3-3814-7689 world wide web - http://www.ddc-web.com the information in this data sheet is believed to be accurate; however, no responsibility is assumed by data device corporation for its use, and no license or rights are granted by implication or otherwise in connection therewith. specifications are subject to change without notice. please visit our web site at www.ddc-web.com for the latest information.

▲Up To Search▲

Price & Availability of PW-82520R3-530L

	To Download PW-82520R3-530L Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .